A sprayer is a device that uses air suction to spray water or other liquid into the mist and spray it evenly onto other objects.

Features: High efficiency; Convenient operation; Large range of action; Effectively block the droplets that spread and float in the air to achieve effective disinfection, sterilization, and insecticidal effects;

Electric sprayer:
A sprayer is an appliance that uses air suction to turn a medicine or other liquid into a mist and evenly spray it onto other objects;
Features: High efficiency; Convenient operation; Large acting area; Effectively blocking the diffuse and floating droplets in the air, to achieve high-efficiency disinfection, sterilization, and insecticidal effects;
Product parameters:
Rated voltage/frequency: AC220V/50HZ
Power: 1200W
Spray volume: 470ml/min
Fog droplet size: 10-15um
Medicine box capacity: 4.5L
Power cord length: 5M
Hose length: 38cm
manual adjustment
Net weight: 3.6 kg
Carton size: 452340CM; one piece/carton

1 Introduction
The sprayer has a wide range of applications and can be used for sanitation and epidemic prevention in hospitals, restaurants, hotels and other public places. It can also be used in chicken coops and sheep pens. Cowshed, pig pen, etc. It is an ideal electric sprayer with reliable performance and convenient use.

2. Operating Instructions
(1). Close the throttle, and then press the switch to the 0 (OFF) position. Unscrew the lid of the chemical container and add less than 7 liters of solution as needed. Tighten the lid of the chemical tank.
(2). Insert the power socket, turn the throttle valve to the appropriate position, lift the machine by hand or hang it on the shoulder, hold the nozzle, press the switch to I (on), the machine will spray: press the switch to 0 (off ) Position, the machine will automatically shut down
(3). Turn the throttle to adjust the size of the mist and its spray volume. Turning the throttle counterclockwise increases the amount of fog and the fog particles. When the throttle valve rotates clockwise, the amount of mist becomes smaller and the mist particles become smaller until the amount of mist is 0 and the size of the mist is 0.
(4). After use, the throttle valve must be rotated clockwise to prevent liquid from flowing out.
(5). When the lid of the chemical container is tightly sealed, the amount of mist will become larger, and when the lid of the chemical container is not completely sealed, the amount of mist will become smaller. For high performance, be sure to tighten the cover.
(6). Please read the notes carefully.

3. Matters needing attention
(1). The sprayer is not allowed to spray or fill with flammable, explosive and corrosive substances, such as alcohol, gasoline, benzene and high-concentration disinfectant (the disinfectant must be diluted before use)
(2). Please do not use the sprayer in a closed room. After spraying, close the doors and windows to increase the application effect and ensure personal health.
(3). Liquids such as banana oil or gasoline are not allowed to clean the sprayer. When cleaning the exterior of the machine with water or other neutral detergents, be careful not to let low-water or neutral detergents flow into the motor housing.
(4). After each use, the unused liquid must be poured out, and the liquid will not pollute the environment. And it is very important and necessary to add water to the chemical container and start spraying for about 0.5-1 minutes to clean the machine pipes to avoid machine corrosion and extend machine life.
(5). It is forbidden to leave it under high temperature or sunlight for a long time to prevent the machine from being deformed, discolored or cracked by baking.
(6). Do not pull the plug by pulling the power cord. Please grasp the rubber part of the plug to pull the plug by hand

4. Preliminary troubleshooting
If the sprayer has the following faults, a preliminary inspection can be performed to eliminate the fault. If the initial inspection does not solve the problem, you can contact the manufacturer for consultation.

First of all, the motor does not work
(1). Check if the machine power switch is in the I (ON) position
(2). Check whether the plug is firmly inserted or the socket is loose or damaged
(3). Check if the power supply is normal

Second, reduce or reduce the amount of fog
(1). Check whether the pipes inside the machine are folded, twisted, blocked or damaged.
(2). Check if the suction port is blocked
(3). Check the throttle valve for damage
(4). Check if the chemical tank lid is tightly sealed